RegisterDonateLogin

If there's a bright center to the universe, you're on the web site that it's farthest from.

Welcome Guest Active Topics | Members

Fixing limp lightsabers. Options
shadowlost
Posted: Saturday, January 8, 2011 4:13:00 AM
Rank: Uggernaught
Groups: Member

Joined: 4/27/2008
Posts: 34
Location: Columbus, Ohio
I'm trying to correct some of my pieces that have sagging lightsabers. I've tried hot water, hot air, and plastic holders. But they keep going back. Is thete a trick that works? Exar isn't really frightening with limp lightsaber syndrome.
Lily_Wan
Posted: Saturday, January 8, 2011 8:42:18 AM
Rank: Advanced Bloo Milk Member
Groups: Member

Joined: 2/14/2009
Posts: 744
Location: Chicago
I've never been able to correct Exar. Other than Exar and a couple stubborn pieces, though, I use a hair dryer (hot air), reshape the mini and immediately put it into the freezer/icebox, often holding it in place for a few second before closing the freezer door. Freeze about five minutes.
R5Don4
Posted: Saturday, January 8, 2011 8:50:30 AM
Rank: Advanced Bloo Milk Member
Groups: Member

Joined: 3/27/2008
Posts: 832
The best results I have seen are done by completely removing the plastic blade and replacing it with the painted shaft of a pin or needle.
Cordova
Posted: Saturday, January 8, 2011 8:55:06 AM
Rank: Advanced Bloo Milk Member
Groups: Member

Joined: 2/2/2009
Posts: 177
I went for the hot water onto an ice cube.

Hold the model/saber in hot water til it's all floppy, then take it out and straighten. As soon as it's straight hold onto an ice cube and roll it out over it (if that makes sense) to freeze it in the straight position.
jak
Posted: Saturday, January 8, 2011 10:11:17 AM
Rank: Advanced Bloo Milk Member
Groups: Member

Joined: 10/17/2010
Posts: 3,682
Location: Beggers Canyon Tatooine
Blink how common is this limp "lightsaber" problem any way?Confused
LOL I'd try Viagra before I put any "sabers" in boiling water.Scared
l337j3di
Posted: Friday, January 14, 2011 11:52:48 AM
Rank: Massassi Sith Mutant
Groups: Member

Joined: 10/13/2010
Posts: 15
blow dryer fixes all problems
CerousMutor
Posted: Friday, January 14, 2011 6:24:53 PM
Rank: Advanced Bloo Milk Member
Groups: Member

Joined: 8/27/2008
Posts: 990
Take a cotton bud, or q-tip.
Cut it up into a tube, Make the sure its open at both ends too, making a Q-Tube BigGrin
Ensure its long enough to go over the lightsaber blade (make it longer than the blade). Put it over the blade.
Take 2 glasses.
Fill a glass up with ice water and the other with boiled water from a kettle.
Dip the lightsaber hand into the hot water for about 20 seconds. Then Dip it straight into the ice water for about 10 seconds.

Take the Q-Tube off, DONE!
Users browsing this topic
Guest


Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Main Forum RSS : RSS

Bloo Milk Theme Created by shinja
Powered by Yet Another Forum.net.
Copyright © 2003-2006 Yet Another Forum.net. All rights reserved.